ما توصّل إليه النقاش

• ARTEMIS 1 وARTEMIS 2 هما الاسمان الرسميان لـ ARRI منتجا مسجلان كعلامات تجارية إلى جانب TRINITY 1 وTRINITY 2 وSRH3 وSRH360 - وهما ليسا مجرد عاملين مختصرين في التنقيحات الأقدم والأحدث.
• The camera interface is the largest change: ARTEMIS 2 introduces the SAM standard (Stabilizer Adapter Mount), delivered as SAM-2 for ALEXA and SAM-3 for AMIRA, which lets the same camera move tool-free between the stabilizationr, a remote head, a tripod and TRINITY.
• وزادت القدرة على توليد الطاقة بعامل خمسة. وفي الجيل السابق، صنفت أكثرية top stage ناتجا بـ 12 V كحد أقصى قدره 3 ألف؛ و ARTEMIS 2 يقبل 10.6 إلى 33.6 V DC واللوازم 12/24 V حتى 15 ألف.
• The ARTEMIS 2 stages carry data buses the earlier generation did not have: LBUS on a Lemo 0B 4-pin connector at 24 V and a CAN bus on a Fischer 4-pin connector.
• The battery system was rebuilt around 19 mm rods with a BMS-2 base and repositionable mounts, with a jog wheel menu and a simultaneous discharge mode, replacing the mechanical battery hanger with its pendulum and dovetail.
• The 1.8 in carbon centre post family carried over. On the earlier generation it telescopes from 43 to 72 cm (16.9 to 28.3 in) with a fine trim range of 22 mm in total, plus or minus 11 mm; on ARTEMIS 2 the same post is two-stage with a tool-free clamp and tool-free fine trim.
• The gimbal also carried over: 1.8 in post, 15.9 mm (5/8 in) arm posts, no-tool clamp lever, knurled handle at 50.8 mm and curved handle at 26 mm, with a patented self-centring friction ring that aligns the main bearing to the post rather than clamping it.
• ARTEMIS 2 is explicitly designed for conversion to TRINITY 2, and weighs 7.4 kg (16.3 lb).
• The Artemis sold under Sachtler, before ARRI took the line over, uses a 1.5 in centre post. That is the Steadicam standard diameter, so a Tiffen Volt fits a Sachtler Artemis - a cross-manufacturer compatibility that neither company's documentation mentions, because it concerns the other one's product.
• Operators with a first-generation Artemis do ask how to run a Volt on it, repeatedly, and the answer given in the field is that the manufacturer supplies it directly as a set comprising the control block, the cables and the gimbal. The open practical question is where the block mounts on that sled, not whether the post diameter fits.

يعتمد على

• Taken from ARRI product documentation, not from a forum discussion: the ARTEMIS 2 user manual version 1.1 dated 2022-09-01 and the certified TRINITY generation 1 training material.
• Figures describe the state at publication. ARRI states that specifications may change without notice and refers to current data sheets.
• The note on the Sachtler Artemis 1.5 in post and Volt compatibility comes from operator practice, not from a manufacturer document. It applies to the Sachtler-branded Artemis, not to the later ARRI models.

المعدات في هذا النقاش

Artemisالكتالوج, Trinity 1الكتالوج, Trinity 2الكتالوج, Voltالكتالوج

القطع

Dovetail Plate

المعدات أو القطع نفسها

1. 2026Intry-level stabilizationr strategy on a 15,000 USD budget: Rever EVO against used Artemis 2 or M2 plus Volt, in a market with limited secondhand availability.موضع خلافFacebookThe Steadicam Group
2. 2026الاحتكاك والتصوير الحاد في Tiffen gimbals مع Volt كابل طاقة: الأسباب الجذرية ومعايير القبول.موضع خلافFacebookThe Steadicam Group
3. 2026Upgrading an M1 Volt gimbal from 1.5-inch to 1.75-inch center rod: insert replacement procedure and encoder ring considerations.موضع خلافFacebookSteadicam operators group
4. 2026تقلص عدد خطوط الفيديو الخاصة بشركة BNC في ARRI Artemis 1 sled: أماكن العمل المؤقتة والحلول الدائمة.FacebookSteadicam operators group