SteadiHub
2026من مجموعة على Facebook: Arri Artemis Trinity

Los power on Trinity 2 / Artemis 2 with large cameras (A35, Venice): causes and battery solutions.

ملاحظة (حتى أكتوبر 2026)لم يعد كورت أو. شالر، مطوّر أنظمة Artemis وTrinity، يعمل لدى ARRI منذ نهاية عام 2025. على حد علمنا، لا يوجد لدى ARRI حاليًا فريق مخصص ولا جهات اتصال رسمية لأنظمة المثبّتات. نرى أن مستقبل هذا الخط غير مؤكد. إذا كنت تشتري جديدًا، فاحصل مسبقًا من ARRI على تأكيد مكتوب بمدة ضمان الخدمة وقطع الغيار. اطلب من الشركة المصنّعة فحص الأجهزة المستعملة قبل الشراء.
موضع خلافاختلف المشاركون ولم يصلوا إلى خلاصة. اقرأ النتائج على أنها مواقف، لا إجابة.

ما توصّل إليه النقاش

  • One operator confirmed that three 12 V batteries or BeBob 24 V batteries (20 A per unit) provide sufficient current, whereas two Gold Mount batteries consistently cause intermittent shutdowns regardless of brand, age, or charge state; approximately 15 A total demand was observed.
  • The root cause appears to be large current spikes from Trinity motors under load—for example at mechanical stops, when pushed to the limit, or from light cable contact at the outer ring—with demand rising into the high teens of amperes, after which the system and camera power down.
  • Calculated power budget: A35 with EVF approximately 90 W, Teradek approximately 15 W, small monitor approximately 15 W, mini motors less than Preston focus control—totaling roughly 150 W or 6.25 A at 24 V; with 14.4 V batteries and higher loads, realistic draw is 10–12 A.
  • Multiple operators confirmed the problem since day one with A35 and Venice on 14 V batteries; the issue does not occur with 26 V B-Mount batteries; on Venice 1, a 12 V camera cable helped, but on Venice 2 it did not.
  • OS360 users report no such problem, suggesting the issue is specific to Artemis 2 / Trinity 2.
  • ARRI's push toward B-Mount batteries with high ampere output may reflect this power demand; operators are adding a B-Mount battery as a second supply to resolve the dropout.

يعتمد على

  • Actual peak current demand is debated: calculated at 6 A steady-state versus observed spikes in the high teens of amperes.
  • Whether the problem is specific to Trinity 2 or affects earlier stabilizer generations.
  • Camera model and monitor configuration affect total load.
  • Cable routing and mechanical contact can trigger spikes.

المعدات في هذا النقاش

OS 360الكتالوج, ALEXA 35الكتالوج, Artemisالكتالوج, Trinity 2الكتالوج, MDR

المعدات أو القطع نفسها

  1. 2026Upgrading an M1 Volt gimbal from 1.5-inch to 1.75-inch center rod: insert replacement procedure and encoder ring considerations.موضع خلافFacebookSteadicam operators group
  2. 2026Intry-level stabilizationr strategy on a 15,000 USD budget: Rever EVO against used Artemis 2 or M2 plus Volt, in a market with limited secondhand availability.موضع خلافFacebookThe Steadicam Group
  3. 2026تقييم ما إذا كان ينبغي إصلاح نظام " بروفيد 2 " القديم أو الاستثمار في جهاز جديد للعمل على مستوى الدخول steadicamSteadi-Newbies
  4. 2026القضاء على الاهتزاز مع ARRI ALEXA 35 في Steadicam®: خيارات الرفع الصلب للطبقات لتجاوز نظام dovetailFacebookThe Steadicam Group
النقاش الأصلي على Facebook (لأعضاء المجموعة فقط)اسأل عن هذا النقاشالإجابة تستشهد بالأرشيف