What operators found

• The Venice brain unit can be mounted inverted at the sled base using an SOS plate with two screws on the M-1 base, placing the weight below instead of above and allowing the lens to reach floor level without antlers.2020 FacebookDisputed
• The M1 and M2 gimbals share the same bearing size as the PRO gimbal, making PRO pan bearings a direct replacement; operators reported noticeably quieter, smoother operation, better lock-offs, and elimination of fishtailing after the swap.2020 Facebook
• The pan bearing on Steadicam® Volt gimbals shipped from Tiffen often contains thick oil or grease-like residue that causes unstable lock-offs; cleaning and applying a single drop of ARRI camera oil restores smooth performance.2020 FacebookDisputed
• The Pilot arm and vest are not compatible with the Mini sled because the Mini gimbal has only two axes built in, with the third axis mounted on the arm itself, requiring significant modifications for use with other arms.2020 General Discussion
• Practicing with medium-weight rigs offers better balance for building both endurance and operating skill compared to always using very light or very heavy setups.2020 Steadi-Newbies
• A properly balanced gimbal system should maintain balance when rotated 180 degrees on the balancing spud, but some units lose balance after rotation2020 Gimbal

Still argued about

1. 2020Achieving lowmode lens height on a 43 lb Sony Venice Panavision Rialto rig without antlers, using inverted body placement.FacebookThe Steadicam Group
2. 2020Cleaning and lubricating the pan bearing (gimbal head) on Steadicam® Volt systems to restore smooth lock-offsFacebookSteadicam operators group
3. 2020Gimbal handle length trade-offs for camera operationOperating

Often in the same threads

Volt19, Zephyr15, Gimbal Bearing9, Top Stage9, Artemis6, Low Mode6, G-70X3, Master Series3, xARM2

All threads

1. 2020Achieving lowmode lens height on a 43 lb Sony Venice Panavision Rialto rig without antlers, using inverted body placement.DisputedFacebookThe Steadicam Group
2. 2020Tiffen M1/M2 gimbal pan bearing friction: PRO gimbal bearing compatibility, lubrication best practice, and bearing precision differences.FacebookThe Steadicam Group
3. 2020Cleaning and lubricating the pan bearing (gimbal head) on Steadicam® Volt systems to restore smooth lock-offsDisputedFacebookSteadicam operators group
4. 2020Compatibility and payload limitations when mixing Steadicam Pilot and Mini componentsGeneral Discussion
5. 2020Finding optimal practice weight for stabilizer rig training as a beginnerSteadi-Newbies
6. 2020Static balance of an Aero gimbal changes when rotated 180 degrees on the balancing spudGimbal
7. 2020Comparison of camera stabilizer arms for beginners and backup useGeneral Discussion
8. 2020Choosing between converting a Pro gimbal or purchasing a Volt gimbal systemWave/Volt
9. 2020Finding practical training workshops for learning Steadicam operationSteadi-Newbies
10. 2020Monitor and accessory upgrades for Steadicam Zephyr rigsSteadi-Newbies
11. 2020Mounting and using a Garfield mount for steadicam rigsSteadi-Newbies
12. 2020Selecting protective cases and foam for a GPI Pro Sled and Titan Arm camera rigGeneral Discussion
13. 2020Comparison of GPI Pro and Steadicam M-2 stabilizer systems for operators considering an upgradeGeneral Discussion
14. 2020Reconditioning core strength and balance for Steadicam operators returning after period of disuseGeneral Discussion
15. 2020Volt gimbal losing calibration in Pause Mode after firmware upgradeGimbal
16. 2020Choosing a first steadicam rig as a beginner operatorSteadi-Newbies
17. 2020Comparison of auto-horizon stabilization systems for single-operator steadicam rigsWave/Volt
18. 2020Archer 2 gimbal sled pans unintentionally during gimbal rotation with Volt systemGimbal
19. 2020Micro vibrations appearing in low mode footage on stabilizerWave/Volt
20. 2020Volt tilt motor bumping when button is pressed during tiltingWave/Volt
21. 2020Gimbal handle length trade-offs for camera operationDisputedOperating
22. 2020Zoom controller options for broadcast lens systemsGeneral Discussion
23. 2020Volt stabilizer performance with unbalanced camera rigs and heavy lensesWave/Volt
24. 2020Availability of RED Ranger and DXL2 power cables in Los AngelesBatteries/Power
25. 2020Master series arm bottom section produces clunking sounds at boom end positionsArms
26. 2020Vertical play in Tiffen M2 gimbal pan bearing during mode transitionsGimbal
27. 2020Restoration and identification of a vintage DCE/Pro 1 Steadicam sledSled
28. 2020Mounting 16mm film cameras on Steadicam rigs with monitoring considerationsSteadi-Newbies
29. 2020Techniques for maintaining stable camera movement while operating on stairsOperating
30. 2020Practical strategies for wearing masks and face shields while operating Steadicam during pandemic safety protocolsDisputedGeneral Discussion
31. 2020Advice for new Steadicam operators starting their careerDisputedSteadi-Newbies
32. 2020Creaking noises in Aero-30 arm and appropriate lubrication productsArms
33. 2020Gimbal balance asymmetry after rotating orientation on a stabilizer rigSteadi-Newbies
34. 2020Tightening threaded collar connecting MKV carbon fiber post to D-BoxCenter Post
35. 2020Achieving dynamic balance on an Aero 30 gimbal with C300 Mk3 camera setupGeneral Discussion
36. 2020Camera plate options for steadicam builds with cinema camerasSteadi-Newbies
37. 2020Switching between goofy and regular operating stance for steadicam workOperating
38. 2020Using Steadicam rig as tripod alternative to reduce setup timeGeneral Discussion
39. 2020Finding suitable stabilizer vests for very tall operatorsSteadi-Newbies
40. 2020Fitting Steadicam vests to smaller operatorsVests
41. 2020Advice for beginners purchasing and using a Zephyr steadicam rigSteadi-Newbies
42. 2020Identifying and evaluating a used Steadicam Flyer model with red handle and balance knobs for beginner learningSteadi-Newbies
43. 2020Availability of Volt stabilizer compatible with 2-inch gimbal postsDisputedWave/Volt
44. 2020Battery recelling service availability after Ritter Battery closureBatteries/Power
45. 2020Combining a Steadicam Zephyr with a motorized gimbal for stabilized camera workDisputedGeneral Discussion
46. 2020Steadicam Proline equipment quality and practicality compared to established brandsDisputedGeneral Discussion
47. 2020Proaim Orion geared head suitability for practice versus professional useGeneral Discussion
48. 2020Proper balancing technique when operating a gimbal in low modeSteadi-Newbies
49. 2020SmartSystem Matrix One bundle suitability for first-time steadicam purchase and hybrid Ronin 2 compatibilityGeneral Discussion
50. 2020Compatibility of M1 Volt gimbal with different Steadicam brand sleds and armsGeneral Discussion
51. 2020Forum login failures despite correct password entryForum Support
52. 2020Exovest shoulder assembly screws loosening after minor impactVests
53. 2020Modifying a Steadicam Wave with custom power outlets, BNC connectors, and backlit bubble level while reducing height and weightSled
54. 2020Comparison of matte screen protectors for field monitors in various lighting conditionsMonitors
55. 2020Stanton 12pin Hirose right angle adapter cable construction and propertiesGeneral Discussion
56. 2020Headset microphone exchange systems for film set communicationBrackets/Widgets
57. 2020Comparing used Steadicam Flyer and Pilot models for purchase decisionsSteadi-Newbies
58. 2020Selecting a compact 7-inch monitor for Steadicam workMonitors
59. 2020Payload capacity differences between Zephyr Arm and A30 Arm on Zephyr stabilizersSteadi-Newbies
60. 2020Differences between Archer 2 stabilizer models and suitability for various camera systemsGeneral Discussion