SteadiHub
Sign InSign Up

Gimbal

473 threads in the archive

Based on 474 threads · 86 cited

AI draft, not reviewedDraft, written by AI from the archive, every statement linked to its source — not yet reviewed.

Your gimbal is the handle-to-rig bearing, and when it goes wrong you feel it fast: lost balance on a pan usually means an off-center bearing or a post that isn't round 12. Slight play is often normal and can vanish once a camera is on the rig, but if it shows up in flight, tighten the upper bearing ring or the yoke adjustment screws 36373839. Clicks and vibration usually mean something is working loose, so check the top cap, the post and your plates one at a time 5859606162.

The questions 9

Why does my gimbal lose balance when I pan or rotate it?27 threads · latest 2025

In short

Most often the gimbal or pan bearing is off-center, or the post is not round 12. Loose screws, a bent fork, a slipping camera plate or bad dynamic balance can also do it 34.

How the pros do it

  1. Balance the rig on the spud, then rotate it 180 and 90 degrees to see whether balance holds 35.
  2. Rule out loose parts first, since gimbal screws backing out can shift static balance and threadlocker prevents it 3. A post clamp that is slowly loosening can also let the rig drift out of level 6.
  3. Check the cause: an off-center gimbal, a non-round post, or shifting weight 5. A slipping camera plate or wrong dynamic balance can look the same 4.
  4. To center a small gimbal, pull the dust caps and use a two-pin driver on the centering bolts 5. Adjust both sides equally and in tandem 5, so one screw turned in is matched by the other turned out by the same amount 1.
  5. Verify with a slow drop time of 5 to 7 seconds rather than neutral balance 7. A deviation under one degree at typical drop times may be within manufacturing tolerance 1.
  6. If balance stays inconsistent after centering, the bearings may be worn and need service with precision measuring tools 1.
Caution

Improper centering adjustment can cause additional damage, so only do it if you understand the process 1. Over-tightening the pan bearing retention pins can pinch the yoke and distort alignment 8.

Opinions differ here

Some operators say you can center the gimbal yourself, using two screws and a spanner driver or community guides 154. Others say the misalignment typically needs manufacturer service 10, needs professional service 3, or was only fixed by sending the rig in 11.

What changed

Earlier (2006, 2010), centering meant shims between the pan housing and yoke 8 or on either side of the yoke on EFP gimbals made before 2007 9, today (2013, 2020) it is done with two centering screws or bolts adjusted in tandem 15.

Ask a follow-up
How do I clean and lubricate my gimbal bearings, and with what oil?20 threads · latest 2026

In short

Wash the bearing in acetone, isopropanol or denatured alcohol, dry it, then put on one drop of light oil such as ARRI, Panavision or Tri-Flow with PTFE 121314. Less is better, because excess oil adds drag and attracts dirt 1513.

How the pros do it

  1. Pull the gimbal off the post and open only what you need to reach the pan bearing 1617. Full disassembly risks misaligning internal parts, and removing and reinstalling bearings can damage the races 1718.
  2. Soak the bearing in acetone or isopropanol for 5 to 10 minutes, swishing gently, and dry it between cycles 13. Repeat three to four times, since it may still shed particles after 15 minutes 13. Contact cleaner and denatured alcohol also work 12.
  3. Test it after drying by pressing lightly between the inner and outer race and turning slowly 13. Listen and feel for sticky spots or grinding 13.
  4. Put on one drop of oil and turn the bearing moderately fast in both directions to spread it 13. In a multi-operator test, one drop was optimal for every lubricant tried 13. With Tri-Flow PTFE, operators go as low as 0.25 to 1 drop 14.
  5. For oil, use ARRI high-speed oil or Panavision oil 1912. Tri-Flow with PTFE is the established standard, and Mobil Velocite No. 6 is another option 14. ARRI itself specifies Finish Line Wet Bike Lubricant for gimbal bearings 20. A needle-tip dispenser lets you apply a fraction of a drop 14.
  6. Check by ear after you oil it 21. If it grinds or squeaks, add a little oil, and if it stops abruptly, you used too much 21. Clean every couple of months, or monthly in dust 2223.
Caution

Wear eye protection with acetone, because the bearing sheds liquid violently 12. Forcing misaligned parts together on reassembly can permanently damage the bearing races 24.

Opinions differ here

Operators still argue about how much oil, and whether to oil at all 1421. One side says races can run nearly dry, with oil mainly protecting the cage and preventing corrosion 12. Others say running dry wears the bearing faster 2225. On quantity, broad consensus starts at one drop 21. One approach uses 3 to 4 drops at 12, 3, 6 and 9 o'clock for better protection and dust resistance, at the cost of more friction 21.

What changed

Earlier, in 2005, operators put exactly two drops of teflon oil on each bearing race 24, today, in 2026, the Tri-Flow standard is applied very sparingly at 0.25 to 1 drop 14.

Ask a follow-up
Can I retrofit a Volt onto my existing gimbal or sled?16 threads · latest 2026

In short

Often yes, but how depends on your gear: a PRO gimbal can be modified by the manufacturer 26, and a 1.5 inch rig can take the VOLT GK1 kit 27. A Steadicam® Master gimbal can't be retrofitted, so you buy the M2 Volt gimbal separately 28.

How the pros do it

  1. Measure your post first, because the Volt works with posts of 1.75 inches or smaller, including 1.58 and 1.50 inch 29. A 2 inch post currently needs significant modifications 29.
  2. Check your sled against the compatibility list: M1, M2, Archer, Shadow, GPI Pro and Betz rigs work 29. A PRO sled needs an external control box, while the M2 sled has it built in 30.
  3. For a 1.5 inch rig, order the VOLT GK1 kit from Tiffen, which includes docking bracket, control box, power and gimbal cables, gimbal and post adapters 27. Say whether you want Regular or Goofy configuration when you order 27.
  4. For a Master-era post, the M2 Volt gimbal fits through adapters for 1.5, 1.58 and 1.75 inch posts 28. For a PRO post, a used M2 Volt gimbal with insert adapters from 1.75 to 1.5 inch is a cost-effective route 31.
  5. If you retrofit an older sled like the Ultra 2, plan one to two hours because early-2000s Tiffen sleds lack a quick-disconnect top stage 32. Document the cable routing before you take it apart and use Loctite 222 on the tilt motor and pan sensor bracket fasteners 32.
  6. Keep your old gimbal as a backup, because it covers you when the new unit goes in for repairs or updates 33.
Caution

Check power cable compatibility between your camera system and the Volt control box before you plug in, because a mismatch can damage the equipment 27. Volt 3 can't be used as a conventional gimbal without power, while Volt 2 still works powered down 31.

Opinions differ here

Operators rated the MK-V 2-inch gimbal with Volt as very effective on XCS 2-inch posts 35. Another operator suggested MK-V's The Level might make the Volt unnecessary, and nobody settled which leveling approach is better 35.

What changed

Earlier in 2020, retrofitting a Pro gimbal for Volt was reported as possibly not feasible after manufacturer attempts failed 34, today in 2023 the Volt can be modified to work with a PRO gimbal through professional modification by the manufacturer 26.

Ask a follow-up
Is the play in my gimbal normal, and how do I fix it?14 threads · latest 2026

In short

Slight play is often normal and can disappear once the rig carries a camera 3637. If it shows up in flight, the usual fix is tightening the upper bearing ring or the yoke adjustment screws 3839.

How the pros do it

  1. Load the rig first. Mount the camera on the balance point of the docking bracket, balance the sled, then rotate it 180 degrees to see if it holds static balance 36.
  2. Pan the balanced sled through 360 degrees in 90-degree steps and note where it tilts, because those spots show where spacers go 40.
  3. On a Volt-equipped M-series gimbal, the play usually comes from a loosened upper bearing ring 3841. Lift the sensor ring on top carefully, for example with a razor blade, without destroying its adhesive layer 38. Tighten with the matching spanner or Blue Whale Tool, then verify in Low Mode 3841.
  4. On a Steadicam® Master Series gimbal, pop the dust caps off with a small flathead screwdriver and turn the slot-head screws counterclockwise to remove play 39. Adjust both sides equally and seat the screws only snugly 39. Rebalance with a drop time of 2 to 3 seconds 39.
  5. On an Archer 1, put thin shims between yoke and gimbal on the right sides and test again until it centres 42. Keep spare shims in the kit for emergencies, but treat this as a temporary fix 42.
  6. If you can't tell whether it's in spec, ask the manufacturer 37. They will test the pan bearing on request and replace it if it exceeds limits 37.
Caution

Over-tightening the yoke adjustment screws can jam the very small bearings and cause permanent damage 39. Working around the stabilisation sensor instead of removing it first risks damaging it 46.

Opinions differ here

No consensus was reached on whether the axial play in an M1 is within tolerance 44. One camp says some play is normal and tightening the collar set screws reduces it, while another says to open and tighten at once past a certain threshold 41. The manufacturer calls 1-2mm of vertical pan bearing play in an M2 within normal tolerances 45.

What changed

Earlier, in 2006, a loose Flyer gimbal needed a spacer and a complete strip-down and rebuild, today, in 2022, a loose M1 upper bearing ring gets tightened without disassembling the gimbal 4338.

Ask a follow-up
Which bearings does my gimbal use, and where do I get replacements?13 threads · latest 2026

In short

It depends on the model: the EFP and IIIa take a thin-section angular-contact pan bearing 47, the Master Series takes a 61809ZZ 48, and the Pilot and Solo take a 6807z 49. For PRO and Tiffen M1/M2 gimbals the pan bearing now comes under the SSB name, and Kaydon, Silverthin and New Hampshire Ball Bearings are the named makers and sources for the older types 5047.

How the pros do it

  1. Identify your gimbal first, because the bearing differs by model 494847.
  2. For the EFP and IIIa, the pan bearing is a thin-section type, listed as SSRAI3026ZKERA5P36L02P, about 1.625 x 1.875 x 0.155 in, with New Hampshire Ball Bearings named as a source 47. A full IIIa pan replacement needs two bearings, and the 2004 dimensions came from an EFP bearing, not a measured IIIa 51.
  3. The Pilot and Solo gimbals use a 6807z bearing 49. The Master Series uses a 61809ZZ 48.
  4. For a Tiffen M1 or M2, the PRO pan bearing is a direct replacement because the bearing size is the same 52. The PRO pan bearing is now supplied under the SSB name instead of Kaydon, and the bearing itself is identical 50. Tiffen sells its own replacement for around USD 800 53.
  5. Pull the old bearing and measure it before you order anything 47. Kaydon and Silverthin bearings in one-off quantities are described as very expensive and months away 47.
  6. Check a suspect race by holding the inner ring between two spread fingers and spinning the outer one, which should run freely for several seconds 47. Keep cleaned old bearings as reserves 54.
Caution

Flying a rig heavier than the design weight over-stresses the gimbal bearing races, so a rough gimbal is not always a bad bearing 47. ARRI advises against owner cleaning, lubrication or modification of the ARTEMIS gimbal because of the risk of permanent accuracy damage 57.

Opinions differ here

One report says a late-2021 M2 Volt came with a Kaydon bearing that looked identical to PRO's, making a retrofit unnecessary 55. Others report better performance with PRO-specified bearings in Tiffen gimbals, and Tiffen discouraged fitting third-party PRO bearings 5653. Whether to lubricate at all is also disputed: some run them dry, others use a drop or two of oil 47.

What changed

Earlier, in 2004, the IIIa pan bearing was described as a Thinnex angular-contact bearing 51, today, in 2026, the PRO pan bearing is supplied under the SSB name instead of Kaydon 50.

Ask a follow-up
Why does my gimbal vibrate or click, and how do I stop it?12 threads · latest 2026

In short

Clicking usually means something is working loose, such as the gimbal top cap, the ring holding the top stage to the post, or the post foot 5859. Vibration usually comes from loose plates, batteries, monitor mounts or an extended post, so you eliminate them one at a time 606162.

How the pros do it

  1. Lift the whole rig and shake it to hear what moves 63. Then hold it and tilt it without the balancing dock to tell sled noise from gimbal noise 58.
  2. Settle the camera side first, because every loose joint is amplified at speed 60. Power the camera from the sled, remove the battery bracket, and put soft hook-and-loop on the Gold-Mount and AB battery plates 60. If it still shakes, test the camera on a shoulder rig to rule out the lens 63.
  3. For clicking in the gimbal, tighten the top cap by hand or very slightly with a spanner wrench 58. Check the ring securing the top stage to the post, and the collars at the top and bottom of the post 5963.
  4. On the top stage, tighten the front-to-back worm gear with the provided tool while the camera is on the rig 59. Also check the yoke-to-handle bolts by pulling the gimbal off its post 63.
  5. If you are near max weight with the post fully extended, shorten the post and strap weight as low as possible on the gimbal 62. Check monitor brackets too, since loose fasteners there cause serious vibration 61.
  6. On a long Trinity setup, wedge a small shim between camera top and ring; if the vibration disappears, you need upper support 64. On a Volt gimbal, belt tension that is too low generates vibration at speed, so check that it is calibrated 60.
Caution

Over-tightening the gimbal top cap with tools can permanently lock the threads 58. Over-tightening a roll belt, or skipped belt teeth, needs factory repair, so talk to the service center first 66.

Opinions differ here

Operators don't agree on the main culprit in a vibrating rig: camera and battery setup, arm and running technique, or Volt belt tension 60. On the Trinity, the manufacturer's TAB-1 bracket is the recommended upper support 64, but other operators call it impractical and prefer a wooden wedge, or fly without a top mount 66.

What changed

Earlier, in 2009, the manufacturer called gimbal clunking at 60-70 degrees of tilt normal 65, today, in 2025, operators chase battery brackets, plates and Volt belt tension one component at a time 60.

Ask a follow-up
How do I get my gimbal properly centered and aligned?12 threads · latest 2024

In short

Rule out balance and handle problems first, then run the 90-degree test and correct centering with the adjustment screws or yoke caps your model has 6768. Some XCS gimbals have no field-adjustable parts, so check your model before you open anything 69.

How the pros do it

  1. Rule out other causes first, because wrong dynamic balance from monitor and battery position can look like a gimbal fault 70. Also check that the thin metal spacer under the gimbal screw is present and no thicker than 0.5 mm, and clean the post and gimbal interior with isopropanol 69.
  2. Check the handle too, since an XCS Ergo handle can have tolerance differences that upset centering on a Pro VZ gimbal 68. On an XCS-Ultimate, swapping a used ergo grip for the original grip restored centering 69.
  3. Test with the camera mounted, not on an empty bench 68. Balance the sled, then pan it 90 degrees and see whether it stays level, using drop times of 4+ seconds for more accurate readings 67.
  4. On an Ultra 2, if the sled tilts after the 90-degree turn, shift it uphill with the adjustment tool 67. Turn both bearing screws by the same number of quarter-turns 67. On an Archer 2, pry the yoke caps off carefully with a small watchmaker's flat-head screwdriver to reach the screws underneath 71.
  5. Repeat in 90-degree increments until the sled stays level in all four static balance positions 72. On an Archer 1 with no adjusting screws, thin shims between yoke and gimbal can remove the play, but that is a temporary fix and you should keep spare shims in the kit 42.
  6. Once it is centered, put weak purple threadlocker on the Archer 2 adjustment screw threads and give it about 12 hours to cure so the setting holds 71. If you send the gimbal in for service, include the center post or preferably the whole rig so the tolerances match your setup 73.
Caution

Move the bearing in only one direction, because tightening in both directions risks damaging the gimbal 67. Repair attempts can make things worse, since the gimbal is the most sensitive component of the rig 69.

Opinions differ here

Operators split on whether you should open the gimbal yourself 6975. One side says XCS gimbals have no field-adjustable components and that attempted repairs can make things worse 69. The other side says you can swap trunnions or adjust the end caps yourself, though one manufacturer flagged user shimming as a warranty issue 7568.

What changed

Earlier, in 2009, V2 gimbals needed shimming to hold alignment 74, today, in 2024, the Archer 2 is re-centered with screws under removable yoke caps 71.

Ask a follow-up
How do I set up my gimbal for low mode?11 threads · latest 2022

In short

Balance the rig for normal drop time, then get the arm clear of the gimbal with a bracket or a bracket-free workaround 7677. Balance the camera with the lens pointing down so the sled doesn't fight the inversion 78.

How the pros do it

  1. Balance for normal drop time, same as in high mode 76. Don't stack weight at the bottom of the post, because that adds pendular movement 76.
  2. Balance the camera with the lens pointing downward, so the sled doesn't try to flip it back to normal during flight 78.
  3. Fit an F, J or D bracket when the gimbal sits high near the camera 77. It puts the arm in the gap between battery and camera so it doesn't foul pans and tilts 77. Check that the aircraft pin passes through the F-bracket with equal spacing on both sides of the hole 78.
  4. Skip the bracket by inverting the monitor image and flipping the footage in post 77. That doesn't work for film cameras printing directly or live-to-air, where nobody can flip the signal 77. If your camera can invert its image digitally, flip it there instead of rotating the rig 79.
  5. A Pro model gimbal has more yoke-to-post clearance than a standard one, which can allow low mode without a bracket 79. A lighter camera lowers the gimbal away from the top stage, and an XCS Ergo handle can remove the need for an F bracket in many situations 79.
  6. For extra height, use a dedicated low mode plate from a rental house 76. It's more rigid and gives a modest height gain over improvised handle clamps 76. An Ergo handle can sit upright with a low mode bracket, and you can add a J-bracket when you need to go lower 80.

What changed

Earlier, in 2006, the F, J or D bracket was the way to keep the arm clear in low mode 77, today, in 2014, operators say a bracket isn't strictly necessary with a Pro gimbal, a lighter camera or an XCS Ergo handle 79.

Ask a follow-up
My gimbal handle keeps loosening or slipping - what do I do?8 threads · latest 2022

In short

If the handle works loose, retighten the 3/32 hex screw and put purple Loctite on it 8182. If your hand is slipping, wrap the handle with tennis racket overgrip 83.

How the pros do it

  1. Retighten the handle screw on a Zephyr with a standard 3/32 hex wrench, which pulls the handle back toward the yoke 81.
  2. Add purple Loctite to the screw, because it can back out completely within days even after you tighten it 82.
  3. Don't crank the screw down hard, since too much torque makes the blue connector piece bind and the gimbal stops moving smoothly 82.
  4. Keep the rig under the 24-pound payload limit, because overloading can loosen the handle screw 81.
  5. If the screw keeps failing, call the manufacturer for replacement parts and a proper repair 84. A 3/8 inch threaded extended shaft bolt, about fifty cents, has served as a temporary fix, but the exact size was reported inconsistently 85.
  6. If your hand is the problem, wrap the post and handle with tennis racket overgrip 83. Bicycle handlebar tape wrapped diagonally and secured with electrical tape also works 86. Pick dark colors, which keep their look longer 83.
Caution

The handle screw or shaft can fail suddenly mid-shot, sometimes after unexpected resistance or heaviness in tilt, so treat that feeling as a warning 85. Don't keep flying a handle that is backing out 82.

What changed

Earlier in 2015 a loosening handle screw was tied to exceeding the 24-pound payload 81, today in 2019 fastener failures are reported on rigs within the stated weight limit, pointing at the design itself 85.

Ask a follow-up

Sources 86

  1. 1Gimbal balance and centering issues when the rig is rotated 180 degreesGimbal forum · 2013
  2. 2Gimbal balance asymmetry after rotating orientation on a stabilizer rigSteadi-Newbies forum · 2020
  3. 3Static balance failing at 180-degree rotation indicates gimbal misalignment or damageSteadi-Newbies forum · 2012
  4. 4Gimbal or gimbal handle not centered: sled balanced in only one pan direction.Facebook · Steadicam operators group · 2021
  5. 5Troubleshooting gimbal balance issues on Aero 30 and Zephyr steadicam rigsSteadi-Newbies forum · 2020
  6. 6Older camera rig losing balance after tilting or movement despite appearing mechanically tightGeneral Discussion forum · 2019
  7. 7Balance issues on Tiffen gimbals after gimbal tuningGeneral Discussion forum · 2019
  8. 8Diagnosing and correcting gimbal balance issues through axis alignment and bearing adjustmentGimbal forum · 2006Disputed
All 86 sources
  1. 9EFP gimbal losing balance after whip-pans and regaining itGimbal forum · 2010
  2. 10Steadicam® balance changes when camera is rotated 180 degreesSteadi-Newbies forum · 2009
  3. 11Gimbal tilting problem in Ultra 1 Steadicam® when camera faces specific directionGeneral Discussion forum · 2025
  4. 12Cleaning and lubricating the pan bearing (gimbal head) on Steadicam® Volt systems to restore smooth lock-offsFacebook · Steadicam operators group · 2020Disputed
  5. 13Cleaning and lubricating the pan bearing in a Steadicam® Ultra 2 gimbal: solvent, oil quantity, and distribution method.Facebook · The Steadicam Group · 2021Disputed
  6. 14Lubricating gimbal bearings after cleaning when Tri-Flow PTFE is unavailable for months.Facebook · Steadicam operators group · 2026Disputed
  7. 15Lubricant selection and maintenance procedures for camera gimbalsGimbal forum · 2005
  8. 16Disassembling an ARRI gimbal bearing for cleaning and oil replacement, removing Loctite-secured housing.SteadiHub · 2025
  9. 17Disassembly and maintenance of a multi-rotor gimbal for cleaning and lubricationGimbal forum · 2009
  10. 18Cleaning and disassembling the Flyer Gimbal bearing assemblyGimbal forum · 2009
  11. 19Cleaning and lubrication procedures for PRO gimbal bearingsGimbal forum · 2007Disputed
  12. 20Lubricating gimbal bearings on the Tiffen M1: ARRI-supplied oil versus Finish Line Wet and Tri-Flow alternatives.Facebook · The Steadicam Group · 2021Disputed
  13. 21Gimbal bearing lubrication: oil quantity, product selection, and the performance versus protection trade-off.Facebook · The Steadicam Group · 2026Disputed
  14. 22Bearing lubricant selection and maintenance for gimbal bearingsGimbal forum · 2014Disputed
  15. 23Lubrication and maintenance procedures for gimbals used in film equipmentGimbal forum · 2006
  16. 24Lubrication and maintenance procedure for a IIIA gimbalGimbal forum · 2005
  17. 25Lubrication oil for gimbal maintenanceGeneral Discussion forum · 2011
  18. 26Retrofitting Volt stabilization system to GPI PRO gimbalGeneral Discussion forum · 2023
  19. 27Compatibility of Volt gimbal with 1.5-inch post rigsGeneral Discussion forum · 2024
  20. 28Upgrading a Steadicam® Master gimbal to Volt specification.Facebook · The Steadicam Group · 2022
  21. 29Compatibility of M1 Volt gimbal with different Steadicam® brand sleds and armsGeneral Discussion forum · 2020
  22. 30M2-Volt gimbal compatibility with GPI-PRO-1-HD sled and control box configurationFacebook · The Steadicam Group · 2021Disputed
  23. 31Gimbal upgrade path for GPI PRO CineLive: Volt 2 now versus Volt 3 or alternative horizon stabilizers (Wave, MK-V Level), and adapter compatibility.Facebook · The Steadicam Group · 2025Disputed
  24. 32Volt retrofit on Steadicam® Ultra 2: installation documentation, motor mounting integrity, and 180-degree balance geometry on the pan axisFacebook · The Steadicam Group · 2021
  25. 33Whether to retain older gimbal equipment when upgrading to Volt M2Gimbal forum · 2021
  26. 34Choosing between converting a Pro gimbal or purchasing a Volt gimbal systemWave/Volt forum · 2020
  27. 35MK-V 2-inch gimbal with Tiffen Volt combination: compatibility, cost, and leveling alternatives.Facebook · The Steadicam Group · 2024Disputed
  28. 36Bearing play in Steadicam® Flyer LE gimbal yoke attachmentGimbal forum · 2010
  29. 37Slight wobble play in gimbal pan bearing: normal tolerance or adjustment needed?Facebook · The Steadicam Group · 2022
  30. 38Eliminating play in a Tiffen M1 gimbal retrofitted with Volt electronics on-set without full disassembly.Facebook · Steadicam operators group · 2022
  31. 39Adjusting play in a Steadicam® Master Series gimbal yoke and balancing it for smooth 180-degree pan without tipping.Facebook · Steadicam operators group · 2026Disputed
  32. 40Servicing EFP and Archer gimbals and addressing freeplay issuesGimbal forum · 2014
  33. 41Play in the gimbal head of a Tiffen M2 with Volt body: causes and tightening procedureFacebook · Steadicam operators group · 2023Disputed
  34. 42Centering and play issues in the Archer 1 gimbal yoke bearing axisGimbal forum · 2015
  35. 43Looseness detected between yoke arms and gimbal post on a new Steadicam® FlyerSteadi-Newbies forum · 2006
  36. 44Axial play in the Tiffen M1 gimbal after bearing replacement and tightening—when is it still within spec?Facebook · The Steadicam Group · 2022Disputed
  37. 45Vertical play in Tiffen M2 gimbal pan bearing during mode transitionsGimbal forum · 2020
  38. 46Play in the sled: where it comes from and what can be fixed on the dayOperator practice forum · 2026
  39. 47The pan bearing in the gimbal: what a Kaydon bearing is, what fails, and what a change of supplier would and would not meanOperator practice forum · 2026
  40. 48Bearing specifications for Master Series gimbal replacementGimbal forum · 2023
  41. 49Gimbal compatibility and bearing specifications across different camera stabilizer modelsGimbal forum · 2023
  42. 50Pan bearing replacement for Steadicam® PRO gimbal: manufacturer change from Kaydon to SSB and supply implicationsFacebook · Steadicam operators group · 2026
  43. 51Replacing pan bearings in an IIIa gimbalGimbal forum · 2004
  44. 52Tiffen M1/M2 gimbal pan bearing friction: PRO gimbal bearing compatibility, lubrication best practice, and bearing precision differences.Facebook · The Steadicam Group · 2020
  45. 53Sourcing a replacement pan bearing for a Tiffen sled when PRO no longer sells them individuallyFacebook · Steadicam operators group · 2022Disputed
  46. 54Gaps between ball races in old Steadicam® PRO pan bearings: normal wear and service life.Facebook · The Steadicam Group · 2024
  47. 55Upgrading the pan bearing in the Tiffen Steadicam® M2 Volt gimbal: comparison with PRO gimbal bearings and Kaydon supplier changes.Facebook · The Steadicam Group · 2021Disputed
  48. 56PRO-Pan bearing sourcing change and specification differences between PRO and Tiffen gimbal bearingsFacebook · The Steadicam Group · 2026
  49. 57ARTEMIS gimbal friction and bearing service: manufacturer claims versus operator experience across multiple gimbal types.SteadiHub · 2025Disputed
  50. 58Clicking sound in Steadicam® Scout gimbal during tilt dropsGeneral Discussion forum · 2014
  51. 59Clicking noise from a gimbal rig during handheld operationSteadi-Newbies forum · 2017
  52. 60Isolating vibration sources in a PRO CineLive rig running at speed: camera plate, battery mounts, gimbal belt tension, and arm cushioning.Facebook · Steadicam operators group · 2025Disputed
  53. 61Vibration issues with MKV 2-inch post and gimbal setupsGeneral Discussion forum · 2012Disputed
  54. 62Vibration issues in gimbal operation at maximum weight capacitySteadi-Newbies forum · 2018
  55. 63Identifying sources of vibration and loose play in camera gimbal systems during productionGimbal forum · 2013
  56. 64Reducing vibrations on ARRI Trinity with long camera setup during horizontal post and tilted head at 45 degrees.Facebook · Arri Artemis Trinity · 2023Disputed
  57. 65Ultra2 gimbal clicking noise and fore-aft balance issues during tiltingGimbal forum · 2009Disputed
  58. 66High-frequency vibrations on ARRI Trinity at steep downward tilt and roll/post rotation: top support point solutions and motor tuning.Facebook · Arri Artemis Trinity · 2024
  59. 67Centering gimbal on an Ultra 2 stabilizerGimbal forum · 2015
  60. 68Gimbal centering issues when using XCS Ergo handle with Pro VZ GimbalGimbal forum · 2017
  61. 69XCS-Ultimate gimbal losing center after purchase; role of the ergo handle and factory precision limits.Facebook · The Steadicam Group · 2021
  62. 70Correcting V2 gimbal pan imbalance and axis misalignment issuesGimbal forum · 2009
  63. 71Re-centering a Tiffen Archer 2 gimbal via hidden adjustment screws under yoke capsFacebook · Steadicam operators group · 2024
  64. 72Centering and balancing a gimbal on an entry-level sled (Glidecam X-Series): learning rig versus upgrade path.Facebook · The Steadicam Group · 2021Disputed
  65. 73ARRI Artemis 2 sled tilting after 180-degree rotation: gimbal centering tolerance and measurement methodology.Facebook · The Steadicam Group · 2023Disputed
  66. 74V2 gimbal axis alignment stability and long-term reliability concernsGimbal forum · 2009Disputed
  67. 75Recentering a GPI PRO Gimbal after Volt conversion: counterweight adjustment and trunnion selection.Facebook · Steadicam operators group · 2022Disputed
  68. 76Proper balancing technique when operating a gimbal in low modeSteadi-Newbies forum · 2020
  69. 77Steadicam® Flyer low mode operation and accessory optionsSteadi-Newbies forum · 2006
  70. 78Balancing and setup procedures for low-mode gimbal operationSteadi-Newbies forum · 2009
  71. 79Operating camera gimbal in low mode without a low mode bracketSteadi-Newbies forum · 2014
  72. 80Mounting an XCS ergo handle in low mode with a bracketGimbal forum · 2015
  73. 81Zephyr gimbal handle loosening due to payload exceeding capacityGimbal forum · 2015
  74. 82Zephyr gimbal handle connection loosens and requires recurring tighteningGimbal forum · 2016
  75. 83Grip solutions for gimbal posts and handles to prevent slipping during operationGeneral Discussion forum · 2022
  76. 84Handle attachment failure on Zephyr gimbal due to loose screwGimbal forum · 2015
  77. 85Gimbal handle fastener failure on Zephyr stabilizerGimbal forum · 2019
  78. 86Improving grip on gimbal handles to prevent slipping from sweatGimbal forum · 2007

What operators found

Still argued about

  1. 2026First stabilizer purchase: Steadicam® Elite (14 kg payload, integrated Volt 3) versus Rever Evo (higher payload) and used-market strategy.FacebookThe Steadicam Group
  2. 2026Adjusting play in a Steadicam® Master Series gimbal yoke and balancing it for smooth 180-degree pan without tipping.FacebookSteadicam operators group
  3. 2026Gimbal bearing lubrication: oil quantity, product selection, and the performance versus protection trade-off.FacebookThe Steadicam Group

Often in the same threads

Volt67, Gimbal Bearing66, Top Stage54, Low Mode50, Zephyr49, Artemis29, Trinity 215, Master Series10, Arm Post19, Dovetail Plate13, Wave10, Follow Focus20

All threads

  1. 2026PRO-Pan bearing sourcing change and specification differences between PRO and Tiffen gimbal bearingsFacebookThe Steadicam Group
  2. 2026Pan bearing replacement for Steadicam® PRO gimbal: manufacturer change from Kaydon to SSB and supply implicationsFacebookSteadicam operators group
  3. 2026First stabilizer purchase: Steadicam® Elite (14 kg payload, integrated Volt 3) versus Rever Evo (higher payload) and used-market strategy.DisputedFacebookThe Steadicam Group
  4. 2026Mounting a Mo-Sys LED-wall tracking sensor on ARRI Trinity 2 with the sensor oriented upward for virtual production.FacebookArri Artemis Trinity
  5. 2026Movcam FlexPro carrier system compatibility with Sony Venice in Rialto Mini configuration on DJI RS gimbalFacebookThe Steadicam Group
  6. 2026Pulling focus manually during Steadicam® operating without an AC: equipment and workflow optionsFacebookSteadicam operators group
  7. 2026Adjusting play in a Steadicam® Master Series gimbal yoke and balancing it for smooth 180-degree pan without tipping.DisputedFacebookSteadicam operators group
  8. 2026Gimbal bearing lubrication: oil quantity, product selection, and the performance versus protection trade-off.DisputedFacebookThe Steadicam Group
  9. 2026Pan-bearing friction and image oscillation in Tiffen gimbals with Volt power cable: root cause and acceptance criteria.DisputedFacebookThe Steadicam Group
  10. 2026Choosing between Wave, Volt 2, and MK-V Level gimbals: performance in wind, rig weight, maintenance, and mode switching.DisputedFacebookSteadicam operators group
  11. 2026Upgrading an M1 Volt gimbal from 1.5-inch to 1.75-inch center rod: insert replacement procedure and encoder ring considerations.DisputedFacebookSteadicam operators group
  12. 2026Removing a PRO gimbal from a VZ grip for conversion to a Volt-modified gimbal.DisputedFacebookSteadicam operators group
  13. 2026EFP gimbal grip binding on the center rod: causes, cleaning, and repair versus replacement options.DisputedFacebookSteadicam operators group
  14. 2026Retrofitting a PRO gimbal bearing into a Tiffen Steadicam® M2 gimbal for improved feel and reduced friction.FacebookSteadicam operators group
  15. 2026Lubricating gimbal bearings after cleaning when Tri-Flow PTFE is unavailable for months.DisputedFacebookSteadicam operators group
  16. 2026Clicking noise and intermittent shaking during fast gimbal rotations.SteadiHub
  17. 2026Trinity 2 tilt and roll drift in standard operation, and MGT-2 remote control connection causing pan and roll instability via LBUS.SteadiHub
  18. 2026Mounting the TIFFEN Volt brain: rigidity comparison between ARRI rod mounts and CamJam mounts to minimize vibrationsDisputedSteadiHub
  19. 2026The pan bearing in the gimbal: what a Kaydon bearing is, what fails, and what a change of supplier would and would not meanOperator practice
  20. 2026Play in the sled: where it comes from and what can be fixed on the dayOperator practice
  21. 2025Pan drift on ARRI Trinity 2 gimbal when docked and balanced—normal bearing play or defect?DisputedFacebookArri Artemis Trinity
  22. 2025Steadicam® Volt 3 firmware update (end 2025): motor power increase, vibration notch filter, and operator feedback on daily studio use.FacebookThe Steadicam Group
  23. 2025Integrating a Betz Wave monitor into a Steadicam® PRO sled via fixed bayonet connectors: balance geometry and operational gains.FacebookThe Steadicam Group
  24. 2025MK-V Level: compact roll-stabilization module, function, pricing, and early operator feedbackDisputedFacebookSteadicam operators group
  25. 2025MK-V Level performance after two weeks on set: Low Mode operation, tilt response settings, and delivery delays in 2025FacebookThe Steadicam Group
  26. 2025Volt 3 presets and motor behavior in practice; compatibility with M2 and upgrade decisions from PRO or M1 sleds.DisputedFacebookThe Steadicam Group
  27. 2025Gimbal upgrade path for GPI PRO CineLive: Volt 2 now versus Volt 3 or alternative horizon stabilizers (Wave, MK-V Level), and adapter compatibility.DisputedFacebookThe Steadicam Group
  28. 2025ARRI Trinity tilt control: MGT-2 joystick in Trinity mode versus Follow Mode with joystick correction for dynamic shotsDisputedFacebookArri Artemis Trinity
  29. 2025Minimizing pan drift on straight architectural shots with ARRI Trinity 2: gyro solutions, sled configuration, and operator technique.FacebookArri Artemis Trinity
  30. 2025Isolating vibration sources in a PRO CineLive rig running at speed: camera plate, battery mounts, gimbal belt tension, and arm cushioning.DisputedFacebookSteadicam operators group
  31. 2025Gimbal rolling and tilting when pressing home button, gyro calibration troubleshooting.SteadiHub
  32. 2025ARRI Trinity 2 remote head firmware instability, pan axis control issues, and calibration procedure to prevent malfunction.SteadiHub
  33. 2025ARTEMIS gimbal friction and bearing service: manufacturer claims versus operator experience across multiple gimbal types.DisputedSteadiHub
  34. 2025Disassembling an ARRI gimbal bearing for cleaning and oil replacement, removing Loctite-secured housing.SteadiHub
  35. 2025Intermittent motor power-up failure on T2 gimbal requiring power cycle resetSteadiHub
  36. 2025Gimbal grip collar friction on the post in cold weather and release methods.SteadiHub
  37. 2025Artemis gimbal friction pan stiffness, DIY lubrication versus factory service, and field serviceability.DisputedSteadiHub
  38. 2025Rigging the Sony Venice 2 on an ARRI Trinity 1: height accommodation, balance, and counterweight solutions.SteadiHub
  39. 2025Zoom control malfunction with Cforce Plus motor and MGT-2 on Trinity 2: joystick returns to zero instead of holding position.SteadiHub
  40. 2025ARRI Artemis 2 sled with Volt post, gimbal options, and comparison with Artemis 1, Trinity 2, and third-party stabilizers.DisputedSteadiHub
  41. 2025MK-V gimbal compatibility with Artemis 2 post and manufacturing lead times.SteadiHub
  42. 2025ARRI Trinity Pan Module: hardware assessment, software challenges, and grip department workflow integration.SteadiHub
  43. 2025Affordable monitor mounting solution for low-mode operation with Axis Volt stabilizerSteadi-Newbies
  44. 2025MK-V Level gimbal development status and production timelineGeneral Discussion
  45. 2025Differences between M-1 and M-2 gimbal designsGeneral Discussion
  46. 2025Delivery delays and technical specifications of the MK-V Level camera stabilization deviceGeneral Discussion
  47. 2025Gimbal positioning on the post affects both drop time and control responsivenessSteadi-Newbies
  48. 2025External motor solutions for zoom and focus control on cinema lenses without servoGeneral Discussion
  49. 2025Gimbal tilting problem in Ultra 1 Steadicam when camera faces specific directionGeneral Discussion
  50. 2025Cleaning the pan bearing of an Archer 2 gimbal without full disassemblyGeneral Discussion
  51. 2024Compact dolly alternatives to the Steadicam® arm for dialogue scenes and operator ergonomicsDisputedFacebookThe Steadicam Group
  52. 2024Gaps between ball races in old Steadicam® PRO pan bearings: normal wear and service life.FacebookThe Steadicam Group
  53. 2024MK-V The Level horizon stabilizer: geometry, weight, and compatibility compared to Wave and AR-Mini systemsDisputedFacebookThe Steadicam Group
  54. 2024Achieving neutral balance on ARRI Trinity 2 without the pendulum in all positions, and balancing the asymmetrical head.DisputedFacebookArri Artemis Trinity
  55. 2024Tiffen Steadicam® Axis with integrated Volt as an upgrade for owner-operators and DPs flying RED V-Raptor on occasional projectsDisputedFacebookThe Steadicam Group
  56. 2024High-frequency vibrations on ARRI Trinity at steep downward tilt and roll/post rotation: top support point solutions and motor tuning.FacebookArri Artemis Trinity
  57. 2024ARRI Trinity 1 Live upgrade (NAB 2024): broadcast mounting plates, tally integration, and control optionsFacebookArri Artemis Trinity
  58. 2024Controlling zoom on a servo lens via MasterGrip MGT-2 over LBUS alongside AC's WCU-4/Hi-5 on ARRI Trinity 2 with RED Komodo XDisputedFacebookArri Artemis Trinity
  59. 2024New Volt prototype with pan axis: whip pans with telephoto and implications for operator skill.DisputedFacebookThe Steadicam Group
  60. 2024Tiffen Volt losing horizon lock in Sticky Mode with motor vibration—systematic fault-finding.FacebookThe Steadicam Group
  61. 2024MK-V 2-inch gimbal with Tiffen Volt combination: compatibility, cost, and leveling alternatives.DisputedFacebookThe Steadicam Group
  62. 2024Cleaning and lubricating the pan bearing on a gimbal, with focus on the Tiffen M2; removal of bearing shrouds for service.FacebookThe Steadicam Group
  63. 2024Tension adjustment of gimbal latch screws on Tiffen Archer 2: absence of factory specification and field workarounds.FacebookThe Steadicam Group
  64. 2024Replacing a broken gimbal clamp on a Volt gimbal and field repair options.FacebookSteadicam operators group
  65. 2024PRO-Rig with Volt gimbal and short gimbal handle: improper arm angle and thumb reach to gimbal collar.DisputedFacebookSteadicam operators group
  66. 2024Re-centering a Tiffen Archer 2 gimbal via hidden adjustment screws under yoke capsFacebookSteadicam operators group
  67. 2024Performance and practical considerations for using the Steadicam Axis in professional productionGeneral Discussion
  68. 2024Compatibility and setup considerations when using Volt gimbal systems with Artemis 2 and M2 sledsGeneral Discussion
  69. 2024Compatibility of Volt gimbal with 1.5-inch post rigsGeneral Discussion
  70. 2023Reducing vibrations on ARRI Trinity with long camera setup during horizontal post and tilted head at 45 degrees.DisputedFacebookArri Artemis Trinity
  71. 2023Flying the ARRI Trinity in X-Mode (Omega-style, camera lateral to body) for table-top passes using tilt control via post rotation.DisputedFacebookArri Artemis Trinity
  72. 2023ARRI Trinity: profile settings for soft tilt stops beyond PID tuningFacebookArri Artemis Trinity
  73. 2023ARRI Trinity 2: handling preference between Yoke and MasterGrip for non-tilt shots, and monitor holder edge interferenceDisputedFacebookArri Artemis Trinity
  74. 2023Remote control setup for ARRI Trinity: OCU-1 and MasterGrip wheel versus standard hand wheels for tilt and roll precision.DisputedFacebookArri Artemis Trinity
  75. 2023Play in the gimbal head of a Tiffen M2 with Volt body: causes and tightening procedureDisputedFacebookSteadicam operators group
  76. 2023ARRI Artemis 2 sled tilting after 180-degree rotation: gimbal centering tolerance and measurement methodology.DisputedFacebookThe Steadicam Group
  77. 2023Upgrading the Volt encoder cable from soft PVC to polyurethane for improved durability on Tiffen Volt and M1 gimbalsFacebookThe Steadicam Group
  78. 2023Introduction of the new three-axis Volt gimbal for Zephyr and Aero: early impressions and open questionsFacebookThe Steadicam Group
  79. 2023Recommended accessories and setup for the Tiffen M2 Volt gimbal systemFacebookSteadicam operators group
  80. 2023Spin-test comparison: ARRI Artemis 2 gimbal versus Tiffen M2 with retrofit PRO bearing for free rotation.DisputedFacebookSteadicam operators group
  81. 2023Stoesso and jitter with Steadicam® Zephyr at maximum load with ARRI Amira and cinema lenses: arm upgrade or vest replacement?FacebookSteadicam operators group
  82. 2023Bearing specifications for Master Series gimbal replacementGimbal
  83. 2023Gimbal compatibility and bearing specifications across different camera stabilizer modelsGimbal
  84. 2023Using gyroscopes with Volt camera stabilizersDisputedGeneral Discussion
  85. 2023Disassembly and cleaning procedure for Pilot/Flyer gimbal bearingsGimbal
  86. 2023Retrofitting Volt stabilization system to GPI PRO gimbalGeneral Discussion
  87. 2022Betz Wave losing horizon stability after pan whips with Sony Venice; slow 10–20 second realignment.FacebookSteadicam operators group
  88. 2022Snaking (lateral drift and parallax) in ARRI Trinity Javelin mode: causes, post-correction limits, and mitigation techniques.DisputedFacebookArri Artemis Trinity
  89. 2022ARRI Trinity system: practical strengths, weaknesses, economics, and return on investment versus traditional Steadicam®.DisputedFacebookThe Steadicam Group
  90. 2022Selecting a used Steadicam® rig under 20 lb capacity for RED Komodo with larger lenses and follow focus.DisputedFacebookSteadicam operators group
  91. 2022360-degree roll on a gimbal head mounted on a vest: locking pan and tilt to maintain smooth rotationFacebookArri Artemis Trinity
  92. 2022Whether the ARRI Artemis 1.74-inch center post for the Tiffen M1 Volt gimbal is a turned-down 1.8-inch post or a purpose-built component.DisputedFacebookArri Artemis Trinity
  93. 2022Docking gimbals below standard height using alternative mounts such as the Betz Wave to raise gimbal position and improve sled ergonomicsFacebookThe Steadicam Group
  94. 2022Measuring the depth of the Steadicam® Zephyr gimbal handle bore for the arm post.FacebookThe Steadicam Group
  95. 2022Axial play in the Tiffen M1 gimbal after bearing replacement and tightening—when is it still within spec?DisputedFacebookThe Steadicam Group
  96. 2022Slight wobble play in gimbal pan bearing: normal tolerance or adjustment needed?FacebookThe Steadicam Group
  97. 2022Restoring a gimbal with severely adhesive-sealed bearings: heating, CNC rework, and bearing replacementFacebookThe Steadicam Group
  98. 2022Upgrading a Steadicam® Master gimbal to Volt specification.FacebookThe Steadicam Group
  99. 2022Tilt motor noise and unusual feel on Tiffen Volt after one year of use: encoder replacement, gimbal re-centering, and balance protocol.DisputedFacebookThe Steadicam Group
  100. 2022Sourcing a replacement pan bearing for a Tiffen sled when PRO no longer sells them individuallyDisputedFacebookSteadicam operators group
  101. 2022Grip tape and wrapping options for gimbal handles: alternatives to factory finish.DisputedFacebookSteadicam operators group
  102. 2022Volt versus Betz Wave 1: sled length, weight, tilt hold, mechanical versus electronic stabilization, and outdoor robustness.DisputedFacebookSteadicam operators group
  103. 2022Archer 2 gimbal with Volt module: balance shifts after 180-degree pan—centering and counterweight adjustment.FacebookSteadicam operators group
  104. 2022Recentering a GPI PRO Gimbal after Volt conversion: counterweight adjustment and trunnion selection.DisputedFacebookSteadicam operators group
  105. 2022Removing a stuck gimbal cover on a Tiffen M1: cooling and leverage techniques.FacebookSteadicam operators group
  106. 2022Eliminating play in a Tiffen M1 gimbal retrofitted with Volt electronics on-set without full disassembly.FacebookSteadicam operators group
  107. 2022ARTEMIS 1 versus ARTEMIS 2: what changed and what carried overManufacturer documentation
  108. 2022Monitor options for low-mode gimbal useGeneral Discussion
  109. 2022Floating gimbal drift during flight on budget steadicam rigsSteadi-Newbies
  110. 2022Using steadicam instead of dolly for precise, planned camera movements in narrative filmmakingGeneral Discussion
  111. 2022Gimbal compatibility with Fujifilm X-T2 camera and lensDisputedGeneral Discussion
  112. 2022Grip solutions for gimbal posts and handles to prevent slipping during operationGeneral Discussion
  113. 2021Volt retrofit on Steadicam® Ultra 2: installation documentation, motor mounting integrity, and 180-degree balance geometry on the pan axisFacebookThe Steadicam Group
  114. 2021Kenyon gyro choice for ARRI Trinity sled: KS2 versus KS4 power and pan-axis interference in mode switching.FacebookArri Artemis Trinity
  115. 2021Gyro stabilizers (Kenyon 4x4 vs. 6x6) on a Steadicam® sled for long live-show work with a 5 kg camera package.DisputedFacebookSteadicam operators group
  116. 2021Executing whip-tilts with the ARRI Trinity in a commercial spot.FacebookArri Artemis Trinity
  117. 2021Steadicam® Zephyr with Panasonic VariCam LT: weight management, gimbal stress, and configuration to prevent breakage.DisputedFacebookSteadicam operators group
  118. 2021Flying a RED Komodo on a Steadicam® PRO II and ARRI Trinity: weight, balance, rigging and accessory mountingFacebookThe Steadicam Group
  119. 2021Choosing between a dedicated lightweight focus system and integrating the AC's Preston setup on ARRI Trinity: balance, workflow, and motor compatibility.DisputedFacebookArri Artemis Trinity
  120. 2021Gyroscope mounting and balancing on the ARRI Trinity: post position, counterweight strategy, and power feed configuration.FacebookArri Artemis Trinity
  121. 2021Removing the top stage of a Tiffen Clipper 2 to swap the gimbal for an M2 or Volt unit.FacebookThe Steadicam Group
  122. 2021Modernizing an Ultra-2 sled: removing the nose, upgrading connection boxes, choosing between Volt or other gimbals, and Bottom-Stage modifications.DisputedFacebookSteadicam operators group
  123. 2021Control layout for ARRI Trinity in live production: positioning tilt joystick, monitor, zoom and focus on the gimbal handle.FacebookArri Artemis Trinity
  124. 2021Protecting the thin Volt encoder cable from snagging and connector failure.FacebookThe Steadicam Group
  125. 2021M2-Volt gimbal compatibility with GPI-PRO-1-HD sled and control box configurationDisputedFacebookThe Steadicam Group
  126. 2021Volt installation in Tiffen gimbal: mechanical improvements and assembly notes.FacebookThe Steadicam Group
  127. 2021Volt gimbal on a GPI PRO sled: spare parts and accessories to order with the rig.DisputedFacebookThe Steadicam Group
  128. 2021XCS-Ultimate gimbal losing center after purchase; role of the ergo handle and factory precision limits.FacebookThe Steadicam Group
  129. 2021Lubricating gimbal bearings on the Tiffen M1: ARRI-supplied oil versus Finish Line Wet and Tri-Flow alternatives.DisputedFacebookThe Steadicam Group
  130. 2021Centering and balancing a gimbal on an entry-level sled (Glidecam X-Series): learning rig versus upgrade path.DisputedFacebookThe Steadicam Group
  131. 2021Gimbal or gimbal handle not centered: sled balanced in only one pan direction.FacebookSteadicam operators group
  132. 2021Cleaning and lubricating the pan bearing in a Steadicam® Ultra 2 gimbal: solvent, oil quantity, and distribution method.DisputedFacebookThe Steadicam Group
  133. 2021Upgrading the pan bearing in the Tiffen Steadicam® M2 Volt gimbal: comparison with PRO gimbal bearings and Kaydon supplier changes.DisputedFacebookThe Steadicam Group
  134. 2021Gimbal handle thread size on Tiffen Steadicam® M2 and ergonomic grip alternativesFacebookSteadicam operators group
  135. 2021Combining a Ronin 2 gimbal with a Steadicam sled for stabilized camera workGeneral Discussion
  136. 2021Gimbal pressure technique and horizon control for steadicam operatorsSteadi-Newbies
  137. 2021Volt stabilizer sled rolling over after calibration on goofy foot setupGeneral Discussion
  138. 2021Whether to retain older gimbal equipment when upgrading to Volt M2Gimbal
  139. 2021Adapting the Volt gimbal to work with XCS camera postsGimbal
  140. 2021Trade-offs between extending telescoping posts for longer rigs versus keeping camera stabilizers compactDisputedSteadi-Newbies
  141. 2021Identifying and accessing spanner screws on gimbal adjustment capsGeneral Discussion
  142. 2020Achieving lowmode lens height on a 43 lb Sony Venice Panavision Rialto rig without antlers, using inverted body placement.DisputedFacebookThe Steadicam Group
  143. 2020Tiffen M1/M2 gimbal pan bearing friction: PRO gimbal bearing compatibility, lubrication best practice, and bearing precision differences.FacebookThe Steadicam Group
  144. 2020Cleaning and lubricating the pan bearing (gimbal head) on Steadicam® Volt systems to restore smooth lock-offsDisputedFacebookSteadicam operators group
  145. 2020Static balance of an Aero gimbal changes when rotated 180 degrees on the balancing spudGimbal
  146. 2020Comparison of GPI Pro and Steadicam M-2 stabilizer systems for operators considering an upgradeGeneral Discussion
  147. 2020Volt gimbal losing calibration in Pause Mode after firmware upgradeGimbal
  148. 2020Archer 2 gimbal sled pans unintentionally during gimbal rotation with Volt systemGimbal
  149. 2020Vertical play in Tiffen M2 gimbal pan bearing during mode transitionsGimbal
  150. 2020Gimbal balance asymmetry after rotating orientation on a stabilizer rigSteadi-Newbies
  151. 2020Achieving dynamic balance on an Aero 30 gimbal with C300 Mk3 camera setupGeneral Discussion
  152. 2020Identifying and evaluating a used Steadicam Flyer model with red handle and balance knobs for beginner learningSteadi-Newbies
  153. 2020Combining a Steadicam Zephyr with a motorized gimbal for stabilized camera workDisputedGeneral Discussion
  154. 2020Proper balancing technique when operating a gimbal in low modeSteadi-Newbies
  155. 2020Compatibility of M1 Volt gimbal with different Steadicam brand sleds and armsGeneral Discussion
  156. 2020Evaluating the purchase of a used ActionCam stabilizer rig as a first systemGeneral Discussion
  157. 2020Troubleshooting gimbal balance issues on Aero 30 and Zephyr steadicam rigsSteadi-Newbies
  158. 2020Learning Steadicam operation with malfunctioning budget equipment and no local mentorsSteadi-Newbies
  159. 2020Techniques for operating Steadicam with longer focal lengths like 85mm and aboveSteadi-Newbies
  160. 2020Stabilization tools for film production: MKV Omega-R and Letus Helix Pro comparisonSteadi-Newbies
  161. 2019Balancing a gimbal rig for both static and dynamic stability with heavy cameras and uneven weight distributionSteadi-Newbies
  162. 2019Remote control options for 360-degree camera roll on stabilizer systemsGeneral Discussion
  163. 2019Mounting a monitor on gimbal handle instead of standard sled placementSteadi-Newbies
  164. 2019Using electronic gimbals with vest and arm rigs instead of handheld operationGeneral Discussion
  165. 2019Balancing a gimbal that tilts severely when rotated after servicingGimbal
  166. 2019Gimbal slot depth measurements for Tiffen and GPI Pro gimbalsGimbal
  167. 2019Suitability of small Steadicam rigs like the Aero-15 for run-and-gun solo work versus dedicated camera support systemsSteadi-Newbies
  168. 2019Tiffen M2 steadicam sled specifications and featuresGeneral Discussion
  169. 2019Tuning gimbal parameters when using a lighter camera than the original design specificationGimbal
  170. 2019Gimbal durability and failure when exceeding recommended payload limits on Zephyr steadicam rigSteadi-Newbies
  171. 2019Installing Tiffen M1 Volt gimbal on MKV 1.5 inch camera sledGeneral Discussion
  172. 2019Gimbal handle fastener failure on Zephyr stabilizerGimbal
  173. 2019Pro gimbal tilting during pan movements despite static balanceGimbal
  174. 2019Balance issues on Tiffen gimbals after gimbal tuningGeneral Discussion
  175. 2019Evaluation of used Action Cam Raptor gimbal rig versus Zephyr for first-time purchaseGeneral Discussion
  176. 2019Choosing between upgrading to a Steadicam Pilot Sled or using a DJI Ronin gimbal mounted on an existing Steadicam armSteadi-Newbies
  177. 2019Older camera rig losing balance after tilting or movement despite appearing mechanically tightGeneral Discussion
  178. 2018Achieving dynamic balance on a Flyer LE gimbal systemSteadi-Newbies
  179. 2018Comparison of M1VOLT and WAVE 1 stabilization systems for camera sledsGeneral Discussion
  180. 2018Adjustment and maintenance of screws on the Archer 2 gimbalGimbal
  181. 2018Combining Wave-1 stabilizer with gyro stabilization systemsGeneral Discussion
  182. 2018Sourcing replacement allen bolt for older Pro grip gimbalGimbal
  183. 2018Removing a gimbal from an Ultra1 with Superpost mount for serviceGimbal
  184. 2018Steadicam Merlin 2 setup and balancing challenges for amateur filmmakersSteadi-Newbies
  185. 2018Pro gimbal tilt issues after cleaning and alternative oil useGimbal
  186. 2018Compatibility between M1 gimbal and GPI Pro sled postGimbal
  187. 2018Comparison of Aero 30 and Zephyr camera rigs for stabilization workDisputedSteadi-Newbies
  188. 2018Vibration issues in gimbal operation at maximum weight capacitySteadi-Newbies
  189. 2018Removing a gimbal from a stabilizer sled without cutting cablesGimbal
  190. 2017Clicking noise from a gimbal rig during handheld operationSteadi-Newbies
  191. 2017Differences between Flyer and Flyer LE camera stabilizersGeneral Discussion
  192. 2017Reducing vibrations on Alexa Mini mounted on Zephyr gimbalGeneral Discussion
  193. 2017Balancing adjustment screws on Tiffen Ultra gimbal sledGeneral Discussion
  194. 2017Steadicam Zephyr setup considerations for flying an Alexa Mini with zoom lensesSteadi-Newbies
  195. 2017Adapting M1 gimbal handle to accept 5/8 inch arm posts instead of the standard 3/4 inchGimbal
  196. 2017Gimbal centering issues when using XCS Ergo handle with Pro VZ GimbalGimbal
  197. 2017Comparison of gimbal grip options for professional gimbal equipmentDisputedGimbal
  198. 2017Using a motorized gimbal on a steadicam arm with a steadimate adapterGeneral Discussion
  199. 2017Gimbal balance requiring minor readjustment after mounting sled to body despite proper dock balancingGeneral Discussion
  200. 2017Controlling roll axis on M15 movie controller gimbal and using mimic modeGimbal
  201. 2016Operating a Steadicam inverted for part of a long continuous take without using a low-mode bracketSteadi-Newbies
  202. 2016Reducing unwanted side-to-side movement when using Steadimate vest with motorized gimbalSteadi-Newbies
  203. 2016Gimbal arm post clamp placement and bearing stressGeneral Discussion
  204. 2016Introduction and specifications of new Steadicam Aero 15 and Aero 30 modelsGeneral Discussion
  205. 2016Adding three-axis gimbals to steadicam operator kits for film and television workGeneral Discussion
  206. 2016Follow focus solutions for cameras mounted on the DJI Ronin-MX gimbalGimbal
  207. 2016Comparison of Artemis Maxima and Movi gimbals for camera stabilizationGeneral Discussion
  208. 2016Gimbal and steadicam compatibility with Blackmagic URSA Mini 4.6KGeneral Discussion
  209. 2016Qbranch Omega Lite gimbal system problems and potential solutionsDisputedGeneral Discussion
  210. 2016Operating an Alexa mini camera system on a DJI Pilot droneGeneral Discussion
  211. 2016Center of gravity positioning and dynamic balance setup for a Merlin2 gimbalSteadi-Newbies
  212. 2016Brushless gimbal systems for professional film production and integration with existing camera support equipmentGeneral Discussion
  213. 2016Finding replacement low mode pin for Ultra1 gimbal F-bracketGimbal
  214. 2016Eliminating axis spinning during steadicam drop test after achieving static balanceSteadi-Newbies
  215. 2016Balancing a Smoothee smartphone gimbal with an added anamorphic auxiliary lensSteadi-Newbies
  216. 2016Zephyr gimbal handle connection loosens and requires recurring tighteningGimbal
  217. 2016Identifying and servicing vintage mystery gimbalsGimbal
  218. 2015Evaluating and purchasing a used Pilot stabilizer with HDMI modificationSteadi-Newbies
  219. 2015Balancing a Steadicam rig: step-by-step procedure and common issuesSteadi-Newbies
  220. 2015Hand placement and finger positioning for steadicam gimbal operationSteadi-Newbies
  221. 2015Zephyr gimbal handle loosening due to payload exceeding capacityGimbal
  222. 2015Practical experience with the Sachtler Artemis Trinity stabilizer prototype and production modelGeneral Discussion
  223. 2015Ergonomic concerns and practical limitations of stabilization equipment including gimbals and exoskeleton rigsGeneral Discussion
  224. 2015Removing a VZ gimbal from a professional sledGimbal
  225. 2015Handheld stabilization rig concept using counterbalanced arms and gimbal for small camerasGeneral Discussion
  226. 2015Centering and play issues in the Archer 1 gimbal yoke bearing axisGimbal
  227. 2015Centering gimbal on an Ultra 2 stabilizerGimbal
  228. 2015EFP gimbal balance shifts during 180-degree panning while on docking pinGimbal
  229. 2015Gimbal rubbing against handle in low mode with inverted cameraGimbal
  230. 2015Market competition between steadicam operators and handheld electronic gimbals in film and television productionGeneral Discussion
  231. 2015Finding replacement gimbal parts for S40 steadicam when manufacturer defects occurGimbal
  232. 2015Mounting an XCS ergo handle in low mode with a bracketGimbal
  233. 2015Handle attachment failure on Zephyr gimbal due to loose screwGimbal
  234. 2015Allen wrench sizes needed for Steadicam Zephyr gimbal handle and clamp adjustmentsGimbal
  235. 2015Comparison of Movi M15 gimbal controllers: Movi Controller versus Spektrum DX7sGimbal
  236. 2015Zephyr gimbal clamp difficult to open by handGimbal
  237. 2015Choosing between budget steadicam and gimbal for video stabilizationSteadi-Newbies
  238. 2014Gimbal handle compatibility across different gimbal brands and the mechanical issues with cross-brand mountingGimbal
  239. 2014Control options and compatibility for the DJI Ronin gimbalDisputedGimbal
  240. 2014Executing a continuous one-shot film sequence using multiple camera stabilization techniquesGeneral Discussion
  241. 2014Compatibility of Steadicam Zephyr HD with Arri Alexa camerasGeneral Discussion
  242. 2014Using a DJI Ronin gimbal on a Steadicam arm via an adapter instead of a traditional sledSteadi-Newbies
  243. 2014Motorized exoskeleton arm rigs for gimbal and camera supportDisputedGeneral Discussion
  244. 2014New camera support and monitoring equipment announced at IBC 2014General Discussion
  245. 2014Techniques and time requirements for transitioning a Steadicam rig to low mode operationGeneral Discussion
  246. 2014Electronic roll and tilt stabilization added to steadicam via brushless gimbal headGeneral Discussion
  247. 2014Emergency repair options for a damaged gimbal kip handle locking mechanismGeneral Discussion
  248. 2014Replacing a bent gimbal yoke-to-gimbal connecting screwGimbal
  249. 2014Comparison between Archer2 and Clipper2 camera stabilizers for film workSteadi-Newbies
  250. 2014Loose gimbal collar connection on Zephyr causes horizontal play during tiltsGimbal
  251. 2014Fine adjustment options for steadicam head positioningGeneral Discussion
  252. 2014Mounting a brushless gimbal on a steadicam for extended camera movement range and combined stabilizationDisputedGeneral Discussion
  253. 2014Managing thick Triax cable on Steadicam rigs to minimize impact on camera stabilityGeneral Discussion
  254. 2014Clicking sound in Steadicam Scout gimbal during tilt dropsGeneral Discussion
  255. 2014Veracity control wheels for gimbal operators using RC transmittersOff Topic
  256. 2014Bearing lubricant selection and maintenance for gimbal bearingsDisputedGimbal
  257. 2014Combining Steadicam and MoVI gimbal systems for enhanced camera movementGeneral Discussion
  258. 2014Post extension causes vibrations on Flyer LE with Epic gimbal setupSteadi-Newbies
  259. 2014Docking bracket length and dynamic balancing technique for Glidecam X-22 gimbalDisputedSteadi-Newbies
  260. 2014Solo steadicam operation for documentary production and capability to manage focus while operatingGeneral Discussion
  261. 2014Operating camera gimbal in low mode without a low mode bracketSteadi-Newbies
  262. 2014Comparison of PRO and XCS gimbals for camera rigsDisputedGimbal
  263. 2014Servicing EFP and Archer gimbals and addressing freeplay issuesGimbal
  264. 2014Balancing and tuning a lightweight camera rig on a Merlin 1 gimbalSteadi-Newbies
  265. 2014Gimbal balancing issues with stabilizer rig when changing lens weightSteadi-Newbies
  266. 2014Steadicam producing unwanted left-right shake and pan movements during operationSteadi-Newbies
  267. 2014Brushless motor roll cage for horizon stabilization on Steadicam rigsGeneral Discussion
  268. 2013Movi motorized camera head capabilities and limitations compared to Steadicam for professional productionsDisputedGeneral Discussion
  269. 2013Initial stabilizer testing and technique feedback for gimbal operationSteadi-Newbies
  270. 2013Brushless gimbal market composition and custom versus off-the-shelf componentsDisputedGeneral Discussion
  271. 2013Practical considerations for purchasing and using a vintage Steadicam Model III systemDisputedSteadi-Newbies
  272. 2013Battery options for powering RedRock wireless follow focus systems on gimbalsSteadi-Newbies
  273. 2013Routing and securing wired video cables for flying a stabilized camera rigSteadi-Newbies
  274. 2013Balancing a Canon Mark II with 50mm lens and battery grip on a Merlin 2 gimbalSteadi-Newbies
  275. 2013Reducing pendulum motion in handheld gimbal operation during lateral camera positioningSteadi-Newbies
  276. 2013Balancing and tuning a Merlin 2 Steadicam rig with various camera modelsSteadi-Newbies
  277. 2013Identifying sources of vibration and loose play in camera gimbal systems during productionGimbal
  278. 2013Comparison of Steadicam and brushless gimbal stabilization technology for professional film and television productionDisputedGeneral Discussion
  279. 2013Steadicam operation techniques for dynamic fight choreography in feature filmsDisputedJournals
  280. 2013Whether to enable image stabilization on lenses when using a steadicam rigSteadi-Newbies
  281. 2013Troubleshooting side-to-side dynamic imbalance in a gimbal-stabilized camera rigDisputedGimbal
  282. 2013Equipment options for fast-moving dog POV shots in film productionGeneral Discussion
  283. 2013Selection and comparison of thin versus standard BNC cables for video equipmentDisputedGeneral Discussion
  284. 2013Optimizing Steadicam Zephyr sled balance and gimbal positioning for the Canon C500Steadi-Newbies
  285. 2013Weight and balance considerations for camera rigs on Tiffen Steadicam Pilot systemsJournals
  286. 2013Understanding drop time function in Steadicam rigsDisputedSteadi-Newbies
  287. 2013Using a Steadicam Merlin with a Canon 5D Mark III and 70-200mm lensSteadi-Newbies
  288. 2013Gimbal dynamic balance problems with camera resting in tilted positionGeneral Discussion
  289. 2013Micro gimbal stabilizer for GoPro cameras using 3D printing technologyGeneral Discussion
  290. 2013Gimbal drift and balance issues caused by exceeding weight limitsGimbal
  291. 2013Pilot VLB gimbal bearing housing retention issueGimbal
  292. 2013Motorized handheld camera stabilization system capabilities and practical limitationsDisputedGeneral Discussion
  293. 2013Zephyr gimbal sticking and hunting behavior after water exposureGimbal
  294. 2013Balancing a Steadicam Pilot with Sony PMW EX1 cameraSteadi-Newbies
  295. 2013Extended handle options for Pro gimbal to reduce cramping during operationGimbal
  296. 2013Gimbal balance and centering issues when the rig is rotated 180 degreesGimbal
  297. 2013Merlin Steadicam gimbal balance problem where equilibrium only occurs at specific grip anglesDisputedSteadi-Newbies
  298. 2013Gimbal becoming stiff and unresponsive in hot, dusty conditionsGimbal
  299. 2013Market impact and technical assessment of low-cost Chinese stabilizer systems competing with professional Steadicam equipmentGeneral Discussion
  300. 2013Steadicam work on movie productions using low mode, slow movements, and crane step-offs with the Alexa cameraJournals
  301. 2013Identifying a Steadicam SK-2 kit acquired at government auction and assessing its value and practical utilitySteadi-Newbies
  302. 2012Using heavier oil in gimbal bearings to dampen movement on lightweight rigsDisputedGimbal
  303. 2012Compatibility between XCS ERGO handle and Tiffen gimbal designsGimbal
  304. 2012Steadicam Pilot drifting in pan axis despite proper static balanceSteadi-Newbies
  305. 2012Vibration issues with MKV 2-inch post and gimbal setupsDisputedGeneral Discussion
  306. 2012Safe operating weight limits for SK and ProVid gimbalsGimbal
  307. 2012Identifying metal versus plastic gimbal rings in Steadicam Merlin equipmentSteadi-Newbies
  308. 2012Common problems when starting steadicam operation and how to address themSteadi-Newbies
  309. 2012Gimbal post slipping during whip pans and clamp adjustment methodsSteadi-Newbies
  310. 2012Balancing a Steadicam Merlin with Nikon D800 and 14-24mm lens to reduce pendulum oscillationSteadi-Newbies
  311. 2012Selecting an appropriate steadicam rig for beginners wanting to operate professional HD camerasDisputedSteadi-Newbies
  312. 2012Getting started with stabilizer rigs on a budget and practical modificationsSteadi-Newbies
  313. 2012Assessment of a Segway-mounted camera crane system with remote head controlDisputedGeneral Discussion
  314. 2012Tiffen Zephyr gimbal clamp design update addressing mechanical failuresGeneral Discussion
  315. 2012Static balance failing at 180-degree rotation indicates gimbal misalignment or damageSteadi-Newbies
  316. 2012Repair options for broken gimbal clamp on Master series gimbalGimbal
  317. 2012Merlin steadicam losing trim balance when removed from docking bracketSteadi-Newbies
  318. 2012Gimbal play and noise in Pilot rig between handle attachment and pole-mounted sectionDisputedGimbal
  319. 2012Drilling a hole in a gimbal handle to accommodate a low mode bracket pinGimbal
  320. 2012Diagnosing shake and wobble in Steadicam Zephyr footage during walkingSteadi-Newbies
  321. 2012Using a weight cage to balance light cameras on camera rigsSteadi-Newbies
  322. 2011Balancing a Steadicam Pilot rig and understanding drop time for beginnersSteadi-Newbies
  323. 2011Incompatibility issues between XCS Ergo handle and PRO gimbal components causing premature wearGimbal
  324. 2011Balancing a Merlin stabilizer with a bottom-heavy camera configuration and addressing nodding motion during walkingDisputedSteadi-Newbies
  325. 2011Mobile application for calculating dynamic balance in Steadicam rigsDisputedOff Topic
  326. 2011Connecting Canon 7D video output to Scout monitor via BNCSteadi-Newbies
  327. 2011Production approaches and equipment choices for Walmart Soundcheck concert video seriesJournals
  328. 2011Steadicam Merlin rocking motion during operation and balancing techniquesSteadi-Newbies
  329. 2011Using multiple gyroscopes versus single gyroscope for camera horizon stabilization on pendulum mountsSteadi-Newbies
  330. 2011Design philosophy differences between telescope gimbal models: precision manufacturing versus adjustable assemblyGimbal
  331. 2011Achieving smooth steadicam footage with lightweight rigs like the MerlinSteadi-Newbies
  332. 2011Single-camera 3D stereoscopic filming using a Phantom 65 with Russian dual-image lensesGeneral Discussion
  333. 2011Balancing and tuning a GH1 camera on a Merlin gimbal for stable operationSteadi-Newbies
  334. 2011Lubrication oil for gimbal maintenanceGeneral Discussion
  335. 2010Bearing play in Steadicam Flyer LE gimbal yoke attachmentGimbal
  336. 2010Finding and using through-the-lens teleprompters for steadicam workGeneral Discussion
  337. 2010Selecting an appropriate lightweight Steadicam model for property videography workDisputedSteadi-Newbies
  338. 2010Workshop training on Steadicam operating techniques and equipmentJournals
  339. 2010Weight and operational challenges of stereoscopic 3D steadicam rigs using dual F-series camerasGeneral Discussion
  340. 2010Glidecam HD4000 gimbal loses balance when rotated despite achieving static balance in one orientationGimbal
Show more
Ask about GimbalThe answer cites the archive